Call Toll Free: 1-800-882-4959
Please Ask for Internet Sales
2-3/4 Inch WET Core Bits
Hub 1-1/4"-7 / Standard core length: 13"
Additional length bits may be special ordered on select bits at $3.00 per inch
Recommended RPM for best performance
Minimum RPM
868
Remommended RPM
1157
Max RPM
1447
2-3/4" Contractor Grade Wet Core Bits
Cutters Choice CBGH2750 General Purpose Bit
Economically designed to handle the miscellaneous jobs that don't require more expensive solutions.
$109.95
CBGH Spec
General Purpose
Moderate Steel
Diamond Products Standard Gold Bits
Better Quality Diamond and better Coring Value Designed for average duty wet core drilling
$122.00
SOL Spec
General Purpose
Cured Concrete
Cat # 80149
Diamond Products Heavy Duty Orange Bits
Excellent footage and drilling speed. Designed for all types of wet drilling applications with light to moderate steel
$132.80
HOL Spec
General Purpose
Longer Life
Cat # 04992
H38F Spec
Med Aggregate
w/ reinforcement
Cat # 45565
H42Z Spec
Hard River Rock
w/ reinforcement
Cat # 90035
H64L Spec
Asphalt
Block
Cat # 28623
Diamond Products Premium Black Bits
Very high diamond concentration. Premium Black gives maximum footage and drilling speed in all types of drilling applications
$151.60
POL Spec
General Purpose
Longer Life
Cat # 05629
P38Z Spec
Med Aggregate
w/ reinforcement
Cat # 18408
P64L Spec
Asphalt
Block
Cat # 28598
2-3/4" Professional Grade Wet Core Bits
Diamond Products Supreme Silver Bits
Highest quality diamond concentration meant for smaller holes in very heavy steel and medium aggregate
$190.00
UOL Spec
General Purpose
Fast Drilling
Cat # 07177
UOF Spec
General Purpose
with heavy steel
Cat # 07176
2-3/4" Turbo (Fast-Cut) Wet Core Bits
Cutters Choice CBPDT Turbo Bits
Designed with hard conccrete in mind, the softer bonding material on these diamond core bits are designed to allow your diamonds to be applied evenly.
$139.95
CBPDT Spec
Hard Concrete - Moderate Steel
2-3/4" Thin Wall (Hand-Held) Wet Core Bits
Note: All Diamond Products Thin Wall Bits have a 5/8"-11 Hub
Diamond Products Thin Wall Premium Black Bits
Very high diamond concentration. Premium Black gives maximum footage and drilling speed in all types of drilling applications
$112.80
POL Spec
General Purpose
Longer Life
Cat # 18225
P38Z Spec
Med Aggregate
w/ reinforcement
Cat # 26817
Diamond Products Thin Wall Supreme Silver Bits
Highest quality diamond concentration meant for smaller holes in very heavy steel and medium aggregate
$137.20
UOL Spec
General Purpose
Fast Drilling
Cat # 28532
U38Z Spec
General Purpose
with heavy steel
Cat # 45654

Factors that affect Core Drill Motor
performance and your profit margin

Speed
(RPM) - If the speed is too high the bit will polish. If the speed is too low the job will take too long. You will know if the bit is "Polished" or "Glazed" when it stops cutting, you have segments left, and you don't see exposed diamonds. To open up the diamonds try drilling in soft abrasive material like a cinder block. Be careful to not drill very much as you will be wasting diamonds.
Power
Necessary to maintain the proper cutting speed. Efficient cutting means keeping the bit at the right speed.
Water
Not too little and not too much. The right amount removes slurry and keeps the cut clean. Slurry water should look like "Coffee with cream"
Aggregate
You can't see it until you're done, but a good driller can feel the right speed and pressure to cut varying types of aggregate.
Steel
Slows down the cutting process. Maintaining drill motor speed is important. Don't push the bit too hard. Maintain even speed with even pressure.
Bond Specs
Too hard and it takes too long. Too soft and it costs too much money. Remember Hard bond for cutting soft abrasive materials, soft bond for cutting hard materials. "Hard on hard" won't cut, and "soft on soft" won't last.
Proper Alignment
Necessary for good bit life. This means the rig must be properly anchored. A rig can be anchored with concrete anchors, vacuum or a post jack.
Standing on the rig is DANGEROUS and not acceptable
Core Rig Maintenance
Performance, speed and bit life will mean little if your rig has bad shims, bearing and hold down devices.
Wet Core Bits by Size