Call Toll Free: 1-800-882-4959
Please Ask for Internet Sales

Diamond Products M3 Drill Rig Features and Benefits

Diamond Products - "Lightweight & Economical Stair Rigs"
 
M3 Features:
  • Wheel Kit - Anchor models only.
  • Swivel Mast - Combination models only.
  • Single switch / outlet control panel with amp meter. (CB700 Includes LED Amp meter)
  • 1-1/2" square column (mast) with black oxidized finish.
  • 4 leveling screws on the base
  • 6" bit capacity.
  • Combination Rigs purchased with vacuum pump - allow for quick mounting to flat surfaces without drilling an anchor hole.
  • Slide handle permits drilling in tight areas.
  • Compact size for hard to reach drilling areas
  • Ceiling jack helps keep the rig in place as a backup for anchoring or vacuuming the base down. (used with a brace piece: 2x4 or other material).
  • Weka models allow the motor to be unmounted and used "hand-held"
M3 Anchor Base
M3 Combination Base

Diamond Products M3 Drill Rigs Dimensions

M2 Anchor rig dimensions:
  1. 35-1/2 Inches
  2. 29-3/8 Inches
  3. 4-5/8 Inches
  4. 1-1/2 Inch square column mast
  5. 10 Inches
  6. 6-3/4 Inches
Location to drill anchor hole is 12" measured from the center of the motor spindle to the center of the anchor slot on base.
 
M2 Combination rig dimensions:
  1. 35-1/2 Inches
  2. 29-3/8 Inches
  3. 4-5/8 Inches
  4. 1-1/2 Inch square column mast
  5. 12 Inches
  6. 6-3/4 Inches
  7. 1-1/2 Inches
Location to drill anchor hole is 11-1/2" measured from the center of the motor spindle to the center of the vacuum slot on base.

M3 Rigs with Milwaukee 4005 Best for Core Bits 2" to 6-1/2"

Milwaukee
4005
Two Speed
600 RPM
1200 RPM
115Volt
20Amp
M-3 Complete Lightweight Rigs with Milwaukee 4005 Motors
1-1/2" Square Column Masts Rig. For Core Bits up to six inches.
M3 Anchor Rig: P/N 4247010
- Small Anchor Base, 4005 Drill Motor, motor mount, column (mast), carriage, control panel, ceiling jack and wheel kit.
$2,099.95
M3 Combination Rig: P/N 4247443
- Combo/Anchor Vacuum Base, 4005 Drill Motor, motor mount, column (mast), carriage, control panel, ceiling jack and wheel kit (NOTE: Vacuum Pump not included)
$2,129.95
M3 Complete Combination Rig: P/N 4247539
- Combo/Anchor Vacuum Base, 4005 Drill Motor, motor mount, vacuum pump, vacuum gasket column (mast), carriage, control panel, ceiling jack and wheel kit
(NOTE: Same as above but with Vac Pump)
$2,539.95

M3 Stands with Milwaukee 4097 Best for Core Bits 2-3/8" to 8"

Milwaukee
4097
Two Speed
500 RPM
1000 RPM
115Volt
15Amp
M-3 Complete Lightweight Rigs with Milwaukee 4097 Motors
1-1/2" Square Column Masts Rig. For Core Bits up to six inches.
M3 Anchor Rig: P/N 4247003
- Small Anchor Base, 4097 Drill Motor, motor mount, column (mast), carriage, control panel, ceiling jack and wheel kit.
$2,029.95
M3 Combination Rig: P/N 4247438
- Combo/Anchor Vacuum Base, 4097 Drill Motor, motor mount, column (mast), carriage, control panel, ceiling jack and wheel kit (NOTE: Vacuum Pump not included)
$2,079.95
M3 Complete Combination Rig: P/N 4247435
- Combo/Anchor Vacuum Base, 4097 Drill Motor, motor mount, vacuum pump, vacuum gasket column (mast), carriage, control panel, ceiling jack and wheel kit
(NOTE: Same as above but with Vac Pump)
$2,449.95

M3 Stands with Milwaukee 4096 Best for Core Bits 2-5/8" to 9"

Milwaukee
4096
Two Speed
450 RPM
900 RPM
115Volt
20Amp
M-3 Complete Lightweight Rigs with Milwaukee 4096 Motors
1-1/2" Square Column Masts Rig. For Core Bits up to six inches.
M3 Anchor Rig: P/N 4247008
- Small Anchor Base, 4096 Drill Motor, motor mount, column (mast), carriage, control panel, ceiling jack and wheel kit.
$2,099.95
M3 Combination Rig: P/N 4247442
- Combo/Anchor Vacuum Base, 4096 Drill Motor, motor mount, column (mast), carriage, control panel, ceiling jack and wheel kit (NOTE: Vacuum Pump not included)
$2,129.95
M3 Complete Combination Rig: P/N 4247530
- Combo/Anchor Vacuum Base, 4096 Drill Motor, motor mount, vacuum pump, vacuum gasket column (mast), carriage, control panel, ceiling jack and wheel kit
(NOTE: Same as above but with Vac Pump)
$2,539.95

M3 Stands with Core Bore CB700 Best for Core Bits 3-1/2" to 12"

CB700
Two Speed
400 RPM
800 RPM
120Volt
20Amp
M-3 Complete Lightweight Stair Rigs with CB700 Motors
1-1/2" Square Column Masts Rig. For Core Bits up to six inches.
M3 Anchor Rig: P/N 4247011
- Small Anchor Base, CB700 Drill Motor, .motor mount, column (mast), carriage, control panel, ceiling jack and wheel kit.
$1,592.80
M3 Combination Rig: P/N 4247012
- Combo/Anchor Vacuum Base, CB700 Drill Motor, motor mount, column (mast), carriage, control panel, ceiling jack and wheel kit (NOTE: Vacuum Pump not included)
$1,619.20
M3 Complete Combination Rig: P/N 4247013
- Combo/Anchor Vacuum Base, CB700 Drill Motor, motor mount, vacuum pump, vacuum gasket column (mast), carriage, control panel, ceiling jack and wheel kit
(NOTE: Same as above but with Vac Pump)
$2,147.20

M3 Stands with Milwaukee 4004 Best for Core Bits 4" to 14"

Milwaukee
4004
Two Speed
300 RPM
600 RPM
115Volt
20Amp
M-3 Complete Lightweight Rigs with Milwaukee 4004 Motors
1-1/2" Square Column Masts Rig. For Core Bits up to six inches.
M3 Anchor Rig: P/N 4247009
- Small Anchor Base, 4004 Drill Motor, motor mount, column (mast), carriage, control panel, ceiling jack and wheel kit.
$2,099.95
M3 Combination Rig: P/N 4247441
- Combo/Anchor Vacuum Base, 4004 Drill Motor, motor mount, column (mast), carriage, control panel, ceiling jack and wheel kit (NOTE: Vacuum Pump not included)
$2,129.95
M3 Complete Combination Rig: P/N 4247538
- Combo/Anchor Vacuum Base, 4004 Drill Motor, motor mount, vacuum pump, vacuum gasket column (mast), carriage, control panel, ceiling jack and wheel kit
(NOTE: Same as above but with Vac Pump)
$2,519.95

Factors that affect Core Drill Motor
performance and your profit margin

Speed
(RPM) - If the speed is too high the bit will polish. If the speed is too low the job will take too long. You will know if the bit is "Polished" or "Glazed" when it stops cutting, you have segments left, and you don't see exposed diamonds. To open up the diamonds try drilling in soft abrasive material like a cinder block. Be careful to not drill very much as you will be wasting diamonds.
Power
Necessary to maintain the proper cutting speed. Efficient cutting means keeping the bit at the right speed.
Water
Not too little and not too much. The right amount removes slurry and keeps the cut clean. Slurry water should look like "Coffee with cream"
Aggregate
You can't see it until you're done, but a good driller can feel the right speed and pressure to cut varying types of aggregate.
Steel
Slows down the cutting process. Maintaining drill motor speed is important. Don't push the bit too hard. Maintain even speed with even pressure.
Bond Specs
Too hard and it takes too long. Too soft and it costs too much money. Remember Hard bond for cutting soft abrasive materials, soft bond for cutting hard materials. "Hard on hard" won't cut, and "soft on soft" won't last.
Proper Alignment
Necessary for good bit life. This means the rig must be properly anchored. A rig can be anchored with concrete anchors, vacuum or a post jack.
Standing on the rig is DANGEROUS and not acceptable
Core Rig Maintenance
Performance, speed and bit life will mean little if your rig has bad shims, bearing and hold down devices.