Call Toll Free: 1-800-882-4959
Please Ask for Internet Sales

Diamond Products M4 Drill Rig Features and Benefits

Diamond Products - "Multi-Purpose Core Rigs"
 
M4 Features:
  • Reversible slide handle for use on left or right side.
  • Quick release motor mount for use with hand held motors.
  • High strength, hard anodized 1-5/8" x 2" aluminum column (mast).
  • Top carrying handle
  • Carriage Lock
  • 4 leveling screws on the base
  • 6" bit capacity as sold
  • Combination Rigs purchased with vacuum pump - allow for quick mounting to flat surfaces without drilling an anchor hole.
  • Light weight and portable.
  • Combo bases have angle braces for drilling up to 45 degrees.
  • Great for the general contractor (basic drilling) or plumber (hand-held drilling).
M4 Anchor Base
M4 Combination Base

Diamond Products M4 Drill Rigs Dimensions

The hand-held motor quick release allows you to take the motor out and use hand-held.(Weka models only).
 
M4 Combination rig dimensions:
  1. 33-1/8 Inches
  2. 20-3/4 Inches
  3. 7-7/8 Inches
  4. 22-1/4 Inch t
  5. 3-5/8 Inches
  6. 16-7/8 Inches
Location to drill anchor hole is 9-3/4"(combo) and 9-1/4" (anchor) measured from the center of the motor spindle to the center of the vacuum slot on base.

M4 Rigs with Weka 110Volt DK12 Best for Core Bits 2" to 6-1/2"

Weka
DK12
Three Speed
970 RPM
2330 RPM
4400 RPM
115Volt
20Amp

M-4 Complete Core Rigs with Weka DK12 Motors
1-5/8" x 2" Aluminum Column Masts. For Core Bits up to 6"
30" Complete Anchor Rig: P/N 4240010
- Anchor base, mast, carriage, 110Volt DK12 Motor.
$2,249.95
30" Combination Angle Rig
- Combo vacuum base, mast, carriage, without vacuum pump, 110Volt DK12 Motor. P/N 4240046
$2,389.95
30" Combination Angle Rig: P/N 4240001
- Combo vacuum base, mast, carriage, with vacuum pump, 110Volt DK12 Motor.
$2,719.95

M4 Rigs with Milwaukee 4005 Best for Core Bits 2" to 6-1/2"

Milwaukee
4005
Two Speed
600 RPM
1200 RPM
115Volt
20Amp
M-4 Complete Core Rigs with Milwaukee 4005 Motors
1-5/8" x 2" Aluminum Column Masts. For Core Bits up to 6"
M4 Anchor Rig: P/N 4240015
- Small Anchor Base, 4005 Drill Motor, motor mount, column (mast), carriage, control panel, top carry handle and wheel kit.
$1,999.95
M4 Combination Rig: P/N 4240052
- Combo/Anchor Vacuum Base, 4005 Drill Motor, motor mount, column (mast), carriage, control panel, top carry handle and wheel kit (NOTE: Vacuum Pump not included)
$2,179.95
M4 Complete Combination Rig: P/N 4240006
- Combo/Anchor Vacuum Base, 4005 Drill Motor, motor mount, vacuum pump, vacuum gasket column (mast), carriage, control panel, top carry handle and wheel kit
(NOTE: Same as above but with Vac Pump)
$2,509.95

M4 Stands with Milwaukee 4097 Best for Core Bits 2-3/8" to 8"

Milwaukee
4097
Two Speed
500 RPM
1000 RPM
115Volt
15Amp
M-4 Complete Core Rigs with Milwaukee 4097 Motors
1-5/8" x 2" Aluminum Column Masts. For Core Bits up to 6"
M4 Anchor Rig: P/N 4240011
- Small Anchor Base, 4097 Drill Motor, motor mount, column (mast), carriage, control panel, top carry handle and wheel kit.
$1,939.95
M4 Combination Rig: P/N 4240048
- Combo/Anchor Vacuum Base, 4097 Drill Motor, motor mount, column (mast), carriage, control panel, top carry handle and wheel kit (NOTE: Vacuum Pump not included)
$2,119.95
M4 Complete Combination Rig: P/N 4240002
- Combo/Anchor Vacuum Base, 4097 Drill Motor, motor mount, vacuum pump, vacuum gasket column (mast), carriage, control panel, top carry handle and wheel kit
(NOTE: Same as above but with Vac Pump)
$2,449.95

M4 Stands with Milwaukee 4096 Best for Core Bits 2-5/8" to 9"

Milwaukee
4096
Two Speed
450 RPM
900 RPM
115Volt
20Amp
M-4 Complete Core Rigs with Milwaukee 4096 Motors
1-5/8" x 2" Aluminum Column Masts. For Core Bits up to 6"
M4 Anchor Rig: P/N 4240014
- Small Anchor Base, 4096 Drill Motor, motor mount, column (mast), carriage, control panel, top carry handle and wheel kit.
$1,999.95
M4 Combination Rig: P/N 4240051
- Combo/Anchor Vacuum Base, 4096 Drill Motor, motor mount, column (mast), carriage, control panel, top carry handle and wheel kit (NOTE: Vacuum Pump not included)
$2,179.95
M4 Complete Combination Rig: P/N 4240005
- Combo/Anchor Vacuum Base, 4096 Drill Motor, motor mount, vacuum pump, vacuum gasket column (mast), carriage, control panel, top carry handle and wheel kit
(NOTE: Same as above but with Vac Pump)
$2,509.95

M4 Stands with Milwaukee 4004 Best for Core Bits 4" to 14"

Milwaukee
4004
Two Speed
300 RPM
600 RPM
115Volt
20Amp
M-4 Complete Core Rigs with Milwaukee 4004 Motors
1-5/8" x 2" Aluminum Column Masts. For Core Bits up to 6"
M4 Anchor Rig: P/N 4240015
- Small Anchor Base, 4005 Drill Motor, motor mount, column (mast), carriage, control panel, top carry handle and wheel kit.
$1,999.95
M4 Combination Rig: P/N 4240052
- Combo/Anchor Vacuum Base, 4005 Drill Motor, motor mount, column (mast), carriage, control panel, top carry handle and wheel kit (NOTE: Vacuum Pump not included)
$2,179.95
M4 Complete Combination Rig: P/N 4240006
- Combo/Anchor Vacuum Base, 4005 Drill Motor, motor mount, vacuum pump, vacuum gasket column (mast), carriage, control panel, top carry handle and wheel kit
(NOTE: Same as above but with Vac Pump)
$2,509.95

Factors that affect Core Drill Motor
performance and your profit margin

Speed
(RPM) - If the speed is too high the bit will polish. If the speed is too low the job will take too long. You will know if the bit is "Polished" or "Glazed" when it stops cutting, you have segments left, and you don't see exposed diamonds. To open up the diamonds try drilling in soft abrasive material like a cinder block. Be careful to not drill very much as you will be wasting diamonds.
Power
Necessary to maintain the proper cutting speed. Efficient cutting means keeping the bit at the right speed.
Water
Not too little and not too much. The right amount removes slurry and keeps the cut clean. Slurry water should look like "Coffee with cream"
Aggregate
You can't see it until you're done, but a good driller can feel the right speed and pressure to cut varying types of aggregate.
Steel
Slows down the cutting process. Maintaining drill motor speed is important. Don't push the bit too hard. Maintain even speed with even pressure.
Bond Specs
Too hard and it takes too long. Too soft and it costs too much money. Remember Hard bond for cutting soft abrasive materials, soft bond for cutting hard materials. "Hard on hard" won't cut, and "soft on soft" won't last.
Proper Alignment
Necessary for good bit life. This means the rig must be properly anchored. A rig can be anchored with concrete anchors, vacuum or a post jack.
Standing on the rig is DANGEROUS and not acceptable
Core Rig Maintenance
Performance, speed and bit life will mean little if your rig has bad shims, bearing and hold down devices.