120V Core Bore CB733 Core Drill Motor
12" Bit Capacity Motor (16" Max)

3 Speed (Loaded RPMs)	Weight
345 / 630 / 1000	28.4

Mount to the M-1, M-2, and M-5 PRO Drill Rigs

Power: 120 Volts * 20Amp = 2400 Watts * 0.00134102 = 3.218 Horsepower

RPM: 3-Speed Motor 345, 630, 1000 "Loaded" RPM settings.

Thread Size: 1-1/4"-7 Spindle

Weight: 28.4 Lbs.

Add a Drill Rig to your Core Bore CB733 (120Volt)

The Core Bore CB733 Heavy Duty Core Drill Motor is an economical solution for coring holes to 14" in diameter when mounted on a Core Rig (16" with spacer block). This three speed motor is designed for rig mounting for wet core drilling. Set at the high speed (1000RPMs) you can effectively use core bits as small as 2-3/8" in diameter, set on the low speed (225rpms) you can core up to 16"

Up to 14" Bit Capacity with this motor and 16" (1) spacer block

Great for the General Contractor. # 1 Selling Rig in the U.S.A.

M1 Anchor Rig
with CB733 Motor
Vacuum Pump N/A
Mast Height: 44"

M1 Combo Rig
with CB733 Motor
Vacuum Pump Included
Mast Height: 45"

M2 Heavy Duty Core Rigs with 25 Amp 120 Volt CB733 Motor
Up to 14" Bit Capacity with this motor and
16" with one spacer block

The # 1 PRO Rig in the U.S.A.

M2 Anchor Rig
with CB733 Motor
Vacuum Pump N/A
Mast Height: 44"

M2 Combo Rig
with CB733 Motor
Vacuum Pump Included
Mast Height: 45"

The lightest big rig on the Market

M5 Anchor Rig
with CB733 Motor
Vacuum Pump N/A
Mast Height: 42"

M5 Combo Rig
with CB73344 Motor
Vacuum Pump Included
Mast Height: 42"

The fastest professional quick-disconnect

M5 Pro Anchor Rig
with CB733 Motor
Vacuum Pump N/A
Mast Height: 42"

M5 Pro Combo Rig
with CB733 Motor
Vacuum Pump Included
Mast Height: 42"

M1/M2
Vacuum Pump

M5
Vacuum Pump

Bit Sharpening Pot
#60 Aluminum Oxide

Pipe Mount
Specify Core Rig

115 Volt Single Switch Dual Outlet

115 Volt Dual Switch Dual Outlet

115 Volt Digital Dual Switch Dual Outlet

Factors that affect Core Bore CB744 Rig Motor performance and your profit margin

Speed	(RPM) - If the speed is too high the bit will polish. If the speed is too low the job will take too long. You will know if the bit is "Polished" or "Glazed" when it stops cutting, you have segments left, and you don't see exposed diamonds. To open up the diamonds try drilling in soft abrasive material like a cinder block. Be careful to not drill very much as you will be wasting diamonds.
Power	Necessary to maintain the proper cutting speed. Efficient cutting means keeping the bit at the right speed.
Water	Not too little and not too much. The right amount removes slurry and keeps the cut clean. Slurry water should look like "Coffee with cream"
Aggregate	You can't see it until you're done, but a good driller can feel the right speed and pressure to cut varying types of aggregate.
Steel	Slows down the cutting process. Maintaining drill motor speed is important. Don't push the bit too hard. Maintain even speed with even pressure.
Bond Specs	Too hard and it takes too long. Too soft and it costs too much money. Remember Hard bond for cutting soft abrasive materials, soft bond for cutting hard materials. "Hard on hard" won't cut, and "soft on soft" won't last.
Proper Alignment	Necessary for good bit life. This means the rig must be properly anchored. A rig can be anchored with concrete anchors, vacuum or a post jack. Standing on the rig is DANGEROUS and not acceptable
Core Rig Maintenance	Performance, speed and bit life will mean little if your rig has bad shims, bearing and hold down devices.