Diamond Products M5 Drill Rig Features and Benefits
Diamond Products - "Extra Duty Core Rigs" |
M5 Features:
|
M5 Anchor Base
|
M5 Combination Base
|
||
Diamond Products M5 Drill Rigs Dimensions
M2 Anchor rig dimensions:
Location to drill anchor hole is 13-1/2" measured from the center of the motor spindle to the center of the anchor slot on base.
|
 |
M2 Combination rig dimensions:
Location to drill anchor hole is 13" measured from the center of the motor spindle to the center of the vacuum slot on base.
|
||
M5 Rigs with Milwaukee 4005 Best for Core Bits 2" to 6-1/2"
 Milwaukee
4096 Two Speed 450 RPM 900 RPM 115Volt 20Amp |
M-5 Complete Heavy Duty Rigs with Milwaukee 4005 Motors 2-1/2 x 3"" Extruded Aluminum (light weight) Column Masts Rig that is hard anodized to prevent wear. . For Core Bits up to 12" - 20" with spacer. |
|
M5 Anchor Rig: P/N 4220057 - Small Anchor Base, 4005 Drill Motor, motor mount, column (mast), carriage, control panel, ceiling jack and wheel kit. |
$2,309.95
|
|
M5 Combination Rig: P/N 4220022 - Combo/Anchor Vacuum Base, 4005 Drill Motor, motor mount, column (mast), carriage, control panel, ceiling jack and wheel kit (NOTE: Vacuum Pump not included) |
$2,429.95
|
|
M5 Complete Combination Rig: P/N 4220007 - Combo/Anchor Vacuum Base, 4005 Drill Motor, motor mount, vacuum pump, vacuum gasket column (mast), carriage, control panel, ceiling jack and wheel kit (NOTE: Same as above but with Vac Pump) |
$2,709.95
|
|
M5 Stands with Milwaukee 4097 Best for Core Bits 2-3/8" to 8"
Milwaukee
4097 Two Speed 500 RPM 1000 RPM 115Volt 15Amp |
M-5 Complete Heavy Duty Rigs with Milwaukee 4097 Motors 2-1/2 x 3"" Extruded Aluminum (light weight) Column Masts Rig that is hard anodized to prevent wear. . For Core Bits up to 12" - 20" with spacer. |
|
M5 Anchor Rig: P/N 4220059 - Small Anchor Base, 4097 Drill Motor, motor mount, column (mast), carriage, control panel, ceiling jack and wheel kit. |
$2,249.95
|
|
M5 Combination Rig: P/N 4220024 - Combo/Anchor Vacuum Base, 4097 Drill Motor, motor mount, column (mast), carriage, control panel, ceiling jack and wheel kit (NOTE: Vacuum Pump not included) |
$2,369.95
|
|
M5 Complete Combination Rig: P/N 4220009 - Combo/Anchor Vacuum Base, 4097 Drill Motor, motor mount, vacuum pump, vacuum gasket column (mast), carriage, control panel, ceiling jack and wheel kit (NOTE: Same as above but with Vac Pump) |
$2,649.95
|
|
M5 Stands with Milwaukee 4096 Best for Core Bits 2-5/8" to 9"
Milwaukee
4096 Two Speed 450 RPM 900 RPM 115Volt 20Amp |
M-2 Complete Core Rigs with Milwaukee 4096 Motors 2-7/8" Square Column Masts. For Core Bits up to 10" as is, or add spacer blocks and this rig will handle bits up to 36". |
|
M2 Anchor Rig: P/N 4241003 - Small Anchor Base, 4096 Drill Motor, motor mount, column (mast), carriage, control panel, ceiling jack and wheel kit. |
$2,309.95
|
|
M2 Combination Rig: P/N 4241084 - Combo/Anchor Vacuum Base, 4096 Drill Motor, motor mount, column (mast), carriage, control panel, ceiling jack and wheel kit (NOTE: Vacuum Pump not included) |
$2,429.95
|
|
M2 Complete Combination Rig: P/N 4241059 - Combo/Anchor Vacuum Base, 4096 Drill Motor, motor mount, vacuum pump, vacuum gasket column (mast), carriage, control panel, ceiling jack and wheel kit (NOTE: Same as above but with Vac Pump) |
$2,709.95
|
|
M5 Stands with Core Bore CB700 Best for Core Bits 3-1/2" to 12"
 CB700
Two Speed 400 RPM 800 RPM 120Volt 20Amp |
M-5 Complete Heavy Duty Rigs with CB700 Motors 2-1/2 x 3"" Extruded Aluminum (light weight) Column Masts Rig that is hard anodized to prevent wear. . For Core Bits up to 12" - 20" with spacer. |
|
M5 Anchor Rig: P/N 4220086 - Small Anchor Base, CB700 Drill Motor, .motor mount, column (mast), carriage, control panel, ceiling jack and wheel kit. |
$1,989.95
|
|
M5 Combination Rig: P/N 4220085 - Combo/Anchor Vacuum Base, CB700 Drill Motor, motor mount, column (mast), carriage, control panel, ceiling jack and wheel kit (NOTE: Vacuum Pump not included) |
$2,119.95
|
|
M5 Complete Combination Rig: P/N 4220084 - Combo/Anchor Vacuum Base, CB700 Drill Motor, motor mount, vacuum pump, vacuum gasket column (mast), carriage, control panel, ceiling jack and wheel kit (NOTE: Same as above but with Vac Pump) |
$2,579.95
|
|
M5 Stands with Milwaukee 4004 Best for Core Bits 4" to 14"
Milwaukee
4004 Two Speed 300 RPM 600 RPM 115Volt 20Amp |
M-5 Complete Heavy Duty Rigs with Milwaukee 4004 Motors 2-1/2 x 3"" Extruded Aluminum (light weight) Column Masts Rig that is hard anodized to prevent wear. . For Core Bits up to 12" - 20" with spacer. |
|
M5 Anchor Rig: P/N 4220055 - Small Anchor Base, 4004 Drill Motor, motor mount, column (mast), carriage, control panel, ceiling jack and wheel kit. |
$2,299.95
|
|
M5 Combination Rig: P/N 4220020 - Combo/Anchor Vacuum Base, 4004 Drill Motor, motor mount, column (mast), carriage, control panel, ceiling jack and wheel kit (NOTE: Vacuum Pump not included) |
$2,429.95
|
|
M5 Complete Combination Rig: P/N 4220005 - Combo/Anchor Vacuum Base, 4004 Drill Motor, motor mount, vacuum pump, vacuum gasket column (mast), carriage, control panel, ceiling jack and wheel kit (NOTE: Same as above but with Vac Pump) |
$2,699.95
|
|
Factors that affect Core Drill Motor
performance and your profit margin
Speed |
(RPM) - If the speed is too high the bit will polish. If the speed is too low the job will take too long. You will know if the bit is "Polished" or "Glazed" when it stops cutting, you have segments left, and you don't see exposed diamonds. To open up the diamonds try drilling in soft abrasive material like a cinder block. Be careful to not drill very much as you will be wasting diamonds. |
Power |
Necessary to maintain the proper cutting speed. Efficient cutting means keeping the bit at the right speed. |
Water |
Not too little and not too much. The right amount removes slurry and keeps the cut clean. Slurry water should look like "Coffee with cream" |
Aggregate |
You can't see it until you're done, but a good driller can feel the right speed and pressure to cut varying types of aggregate. |
Steel |
Slows down the cutting process. Maintaining drill motor speed is important. Don't push the bit too hard. Maintain even speed with even pressure. |
Bond Specs |
Too hard and it takes too long. Too soft and it costs too much money. Remember Hard bond for cutting soft abrasive materials, soft bond for cutting hard materials. "Hard on hard" won't cut, and "soft on soft" won't last. |
Proper Alignment |
Necessary for good bit life. This means the rig must be properly anchored. A rig can be anchored with concrete anchors, vacuum or a post jack. Standing on the rig is DANGEROUS and not acceptable |
Core Rig Maintenance |
Performance, speed and bit life will mean little if your rig has bad shims, bearing and hold down devices. |